THE EXPERIMENTAL STUDY OF SELF COMPACTING CONCRETE USING PLANTAIN LEAF ASH


THE EXPERIMENTAL STUDY OF SELF COMPACTING CONCRETE USING PLANTAIN LEAF ASH

ABSTRACT

Self-Compacting Concrete is an innovative concrete that does not require vibration for placing and compaction. It is able to flow under its own weight, completely filling formwork and achieving full compaction, even in the presence of congested reinforcement. The hardened concrete is dense, homogeneous and has the same engineering properties and durability as traditional vibrated concrete. Plantain leaf ash are waste and are causing threat to environment in terms of odour and to reduce this problem of this material the project has been undertaken so that it can be used for construction fashion following points attempted

i. To study the properties of Plaintain leaf ash

ii. To blend to mix or replace cement by different % of Plaintain leaf ash

iii. To prepare the concrete by replacing the cement by Plaintain leaf ash

iv. To study the comparativeness

TABLE OF CONTENTS

PAGE  

FRONT PAGE I

CERTIFICATION  II

ACKNOWLEDGEMENT III

DEDICATION IV

ABSTRACT V

TABLE OF CONTENT VIII

CHAPTER ONE 

1.0 INTRODUCTION TO SCC

1.1  NEED FOR SCC

1.2       AIMS AND OBJECTIVE

1.3        SCOPE

1.4        SIGNIFICANCE OF STUDY

1.5 ADVANTAGES OF SCC

1.5.1    DISADVANTAGES OF SCC? 

1.5.2    CONSTITUENTS OF SCC 

1.5.3    PROPERTIES OF SCC  

1.6.0    FUNCTIONAL REQUIREMENT OF SCC

1.7.0 PHYSICAL AND CHEMICAL PROCESS OF SCC

1.8.0       PROBLEM STATEMENT

1.8.1       SCC POTENTIAL BEYOND CONVENTIONAL CONCRETE

1.8.2       SCC AND MEASUREMENT OF ITS FLOW PROPERTIES

CHAPTER TWO 

2.0 LITERATURE REVIEW

CHAPTER THREE  

3.0       EXPERIMENTAL RESEARCH 

3.1.0   GENERAL

3.2 INSTRUMENTATION

3.3 MATERIALS 

3.4 PRELIMINARY TEST

3.5       WORKABILITY TEST METHOS

3.5.1    ABRAM SLUMP CONE TEST

3.5.2 SLUMP FLOW AND T500 TEST

3.5.3 V-FUNNEL TEST 

3.5.4  L-BOX TEST  

CHAPTER FOUR 

4.0   RESULT AND DISCUSSION 

4.1   MIX PROPORTION 

4.2    WORKABILITY TEST METHOD 

4.2.1   V-FUNNEL TEST 

4.2.2   L-BOX TEST 

4.3.0    OBSERVATION AND DISCUSSION 

CHAPTER FIVE 

5.0 CONCLUSION AND RECOMMENDATION 

5.1 PLANTAIN LEAF ASH IN SCC 

5.2 COMPARISON OF PROPERTIES OF SCC WITH NCC 

5.3 RELATIONSHIPS BETWEEN PROPERTY MEASUREMENTS OF SCC 

5.4 CONCLUSION AND RECOMMENDATION 

REFERENCES 

PLATES 

APPENDIX 

LIST OF TABLES

Table 3.5- Chemical composition of O.P.C and plantain leaf ash 49

Table 3.6- Chemical composition of super plasticizer                    50

Table 3.7- Particle size distribution of fine aggregate 51

Table 3.8- Particle size distribution of coarse aggregate 52

Table 3.9- Mixture proportions for plantain leaf ash SCC in kg 52

Table 4.0- V-funnel test result of SCC with plantain leaf ash 53

Table 4.1- L-Box test result of scc with plantain leaf ash 53

Table 4.2 – Compressive strength results 54

Table 4.3- EFNARC Requirement for workability 55

LIST OF FIGURES

Fig 1 -   Graph showing particle size distribution of fine aggregate 56

Fig 2 -   Graph showing particle size distribution of coarse aggregate 56

Fig. 4 – Graph showing V-Funnel test result on plantain leaf ash    57

Fig. 5 – Graph showing L-Box test result on plantain leaf ash    57

Fig. 6-   Relationship between compressive strength of NCC and SCC 58

CHAPTER ONE 

1.0 INTRODUCTION TO SCC

Self-Compacting  Concrete  (SCC),  a  relatively  new  category  of  high  performance concrete,  is  proportioned in such  that  the  concrete  freely  passes  around  and  through reinforcement,  completely  fills  the  formwork  and  consolidates  under  its  own  weight without segregation.  The high flowability of SCC makes it possible to fill the formwork without vibration 

[Khayat, 1999; Khayat et al., 2004].

Developed  in  Japan  in  the  late  1980’s  [Ozawa,  et  al.,  1989], SCC  has  been  a  topic  of research and development  in many  locations, especially  in Japan and Europe  [Ouchi, et al.,  2003].  SCC has been successfully used in numerous applications where normal concrete is difficult to place and consolidate due to reinforcement congestion and difficult access.  Precast, prestressed bridge elements, such as AASHTO Type III girders, have congested reinforcement and tight dimensional geometry, and therefore can benefit from the use of SCC.  

Three  basic  characteristics  are  required  to  obtain  SCC:  high  deformability,  restrained flowability  and  a  high  resistance  to  segregation  [Khayat,  et  al.,  2004].   High deformability  is  related  to  the  capacity  of  the  concrete  to  deform  and  spread  freely  in order to fill all  the space  in  the  formwork.   It  is usually a  function of  the  form, size and quantity  of  the  aggregate,  and  the  friction  between  the  solid  particles,  which  can  be reduced  by  adding  a  high  range  water-reducing  admixture  (HRWR)  to  the  mixture.  Restrained flowability represents how easily the concrete can flow around obstacles, such as reinforcement, and is related to the member geometry and the shape of the formwork.   

Segregation  is  usually  related  to  the  cohesiveness  of  the  fresh  concrete, which  can  be enhanced  by  adding  a  viscosity-modifying  admixture  (VMA)  along with  a HRWR,  by reducing  the  free  water  content,  by  increasing  the  volume  of  paste,  or  by  some Combination of these factors.   

Two general types of SCC can be obtained:  

(1) Concrete with a small reduction in the coarse aggregate, containing a VMA. 

(2) Concrete with a significant reduction in the coarse aggregate content without any VMA.   

SCC  has  been  claimed  to  offer many  advantages  for  the  precast,  prestressed  industry including  elimination  of  noise  and  problems  related  to  concrete  vibration,  lower  labor cost  per member,  and  faster  casting,  thereby  increasing  productivity. Due to the low water-cement ratio, SCC should have improved to durability and strength.   

Generally, SCC contains a higher cementitious materials  and  lower water-cement  ratio than  conventional  concrete,  and  so  can  provide  relatively  high  strength.   The paste usually includes fly ash, slag, silica fume, or other supplementary cementitious materials, or an inert filler such as limestone powder. The paste content of SCC  is also  relatively high, with  a  reduction  in  the  size  and  quantity  of  coarse  aggregate.  These factors are typically associated with increased creep and shrinkage, and may be related to a reduction in elastic modulus.  

 WHAT IS SELF-COMPACTING CONCRETE (SCC)? 

It is a concrete that can be compacted by its own weight and fills every corners in the formwork and the placing can be done without vibrating compaction. In the plastic state it is very homogenous, cohesive and very flowable. 

1.1 WHY IT IS NEEDED?

Concrete is a versatile material extensively used in construction applications throughout the world. Properly placed and cured concrete exhibits excellent compressive-force-resisting characteristics and engineers rely on it to perform in a myriad of situations. However, if proper consolidation is not provided, its strength and durability could be questionable. To help alleviate these concerns, Japanese researchers in the late 1980’s developed a concrete mixture that deformed under its own weight, thus filling around and encapsulating reinforcing steel without any mechanical consolidation.  

⦁ Self-Compacting Concrete offers new possibilities and prospects in the context of durability and strength of concrete. 

⦁ As a result of the mix design, some properties of the hardened concrete can be different for SCC in comparison to normal vibrated concrete.  

⦁ Mix design criterions are mostly focused on the type and mixture proportions of the constituents.  

⦁ Adjustment of the water/cement ratio and super plasticizer dosage is one of the main key properties in proportioning of SCC mixtures. 

1.2      AIM AND OBJECTIVES

The aim of this study of self-compacting concrete using Plantain leaf ash as partial replacement of ordinary portland cement is to obtain self-compacting concrete satisfying EFNARC guidelines and make comparison of self-compacting concrete to normally compacted concrete in terms of workability and compressive strength.

The above aim will be accomplished by fulfilling the following research objectives:

1. Determining the effect of Plantain leaf ash as partial replacement of cement on the properties of SCC in

⦁ FRESH STATE (Filling ability and Passing ability)

⦁ HARDENED STATE (Compressive strength)

2. Obtaining specific experimental data to understand fresh and hardened properties of self-compacting concrete.

3. Developing SCC using Plantain leaf ash as partial replacement of cement in varying dosages satisfying European standards and to study their behaviour.

4. Determining whether the properties observed in (1) are structurally sufficient for its application according to relevant standard as a construction material. 

5. Assessing the implication of its usage as a construction material in the built environment 

1.3    SCOPE OF STUDY

For this study, concrete with varied percentages of Plantain leaf were used in producing self-compacting concrete in terms of filling ability and passing ability and were compared with normally compacted concrete.. The key parameter in the study is:

i. The workability characteristics using slump flow test, V-funnel test, L-box test and compressive strength characteristics at 14, 21 and 28 days using 45 cubes of 150mm X 150mm X 150mm were determined.

1.4 SIGNIFICANCE OF STUDY

1. To produce concrete of high and significant strength and durability to be used for all construction structures.

2. To effectively utilize and solve the problem of the storage and disposal of plantain leaf ash.

3. To minimize maintenance, labour cost, and cost due to the vibrators required.

1.5.0 ADVANTAGES OF SELF-COMPACTING CONCRETE: 

Simple inclusion even in complicated formwork and tight reinforcement: 

1. Higher installation performance since no compaction work is necessary which leads to reduced construction times, especially at large construction sites 

2. Reduced noise pollution since vibrators are not necessary 

3. Higher and more homogenous concrete quality across the entire concrete cross-section, especially around the reinforcement  

4. Improved concrete surfaces (visible concrete quality)  

5. Typically higher early strength of the concrete so that formwork removal can be performed more quickly. 

1.5.1   DISADVANTAGES OF SELF-COMPACTING CONCRETE 

1. SCC requires higher powder and admixture (particularly super-plasticizers) contents than normally compacted concrete and so the material cost is higher. 

2. The increased content of powder and admixture also leads to higher sensitivity of SCC to material variation than that of normally vibrated concrete; thus greater care with quality control is required. 

1.5.2 CONSTITUENTS OF SCC

With regard to its composition, SCC consists of the same components as conventionally vibrated concrete, which are 

⦁ Cement 

⦁ Aggregates 

⦁ Water 

⦁ Chemical Admixtures i.e. Superplasticizers and Viscosity Modifying Agents Mineral Admixtures i.e., fly ash, Silica Fume, etc. 

1.5.3 PROPERTIES OF SCC

Following are the properties of hardened self-compacting concrete:

1. Compressive strength 

SCC compressive strengths are comparable to those of normally compacted concrete made with similar proportions and water cement ratio. There is no difficulty in producing SCC with compressive strength up to 60N/mm2. (http://theconstructor.org/concrete/properties-of-hardened-self-compacting-concrete/7681).

2. Tensile strength

Tensile strengths are assessed indirectly by the splitting test on cylinders. For SCC, both the tensile strengths themselves, and the relationships between tensile and compressive strengths are of similar order to those of normally compacted concrete. (http://theconstructor.org/concrete/properties-of-hardened-self-compacting-concrete/7681).

3. Bond strength

The strength of the bond between concrete and reinforcement are assessed by pullout tests, using deformed reinforcing steel of two different diameters, embedded in concrete prisms. For both civil engineering and housing categories, the SCC bond strengths, related to the standard compressive strengths, were higher than those of the reference concrete were. (http://theconstructor.org/concrete/properties-of-hardened-self-compacting-concrete/7681).

4. Modulus of elasticity

Previous results available indicate that the relationships between static modulus of elasticity and compressive strengths were similar for SCC and the reference mixes. A relationship in the form of E/ (fcu) 0.5 has been widely reported, and all values of this ratio were close to the one recommended by ACT for structural calculations for normal weight compacted concrete. (http://theconstructor.org/concrete/properties-of-hardened-self-compacting-concrete/7681).

5. Shrinkage and creep

None of the results obtained indicates that the shrinkage and the creep of the SCC mixes were significantly greater than those of traditional vibrated concrete. (http://theconstructor.org/concrete/properties-of-hardened-self-compacting-concrete/7681)

6. Some aspects of durability

Elements of all types of concrete have been left exposed for future assessment of durability but some preliminary tests have been carried out. 

The permeability of the concrete, a recognized indicator of likely durability, has been examined by measuring the water absorption of near surface concrete. The results suggest that in the SCC mixes, the near surface concrete was denser and more resistant to water ingress than in the reference mixes. Carbonation depths have been measured at one year. (http://theconstructor.org/concrete/properties-of-hardened-self-compacting-concrete/7681)

1.6.0 FUNCTIONAL REQUIREMENT OF SCC

According to EFNARC specification (European Federation of National Association Representing for Concrete), SCC must be designed to fulfil the requirements of EN 206 regarding density, strength development, final strength and durability which obtains the following requirements. 

⦁ Filling Ability – The ability of SCC to flow under its own weight into and fill completely all spaces within intricate formwork, containing obstacles, such as reinforcement. 

⦁ Passing Ability – The ability of SCC to flow through openings approaching the size of the mix coarse aggregate, such as the spaces between steel reinforcing bars, without segregation. 

⦁ Resistance to Segregation – The ability of SCC to remain homogeneous during transport, placing, and after placement. 

1.7.0 PHYSICAL AND CHEMICAL PROCESS OF SCC 

⦁ The physical process is due to the particles fineness of the supplementary cementing materials that are much smaller than that of the cement, thereby providing densely packed particles between fine aggregates and cement grains, and, hence, the reduction in porosity.  

⦁ The chemical process is due to the activation of the non-crystalline silica, by the calcium hydroxide produced from the hydrating cement to form secondary calcium silicate hydrate that also fills the pore spaces and further reduces the porosity 

1.8.0 PROBLEM STATEMENT  

There are currently not universally accepted design, proportioning or acceptance criteria for the use of SCC in prestressed girders.   Although SCC has been used successfully in several  precast  and  cast-in-place  applications  and many  of  the  properties  of SCC  have Been established, several issues must still be resolved in order to successfully use SCC in The production of prestressed bridge elements.  Many of these concerns are related to long term behaviour of the element in service.   

SCC  is  similar  to  conventional  concrete  in  terms  of  compressive  strength.  Due to the lower  content  of  coarse  aggregate,  however,  there  is  some  concern  that:  

(1) SCC may have  a  lower  modulus  of  elasticity,  which  may  affect  deformation  characteristics  of prestressed  concrete  members  

(2) Creep and shrinkage will be higher, affecting prestress loss and long term deflection.   

1.8.1 SCC POTENTIALS BEYOND CONVENTIONAL CONCRETE 

1. Improved efficiency 

2. Use with close meshed reinforcement 

3. For slender Component 

4. For complex geometric shapes 

5. Generally where compaction is difficult  

6. Fast installation rates 

7. Reduced damage to health 

1.8.2 SCC AND MEASUREMENT OF ITS FLOW PROPERTIES

Conventional workability tests, devised for normal ranges of concrete mixtures are not adequate for self-compacting concrete, because they are not sensitive enough to detect the tendency to segregation. For example, a slump test may show collapse, (a slump of say 280 mm) and yet in one case the mixture may be stable and in other cases either the aggregate may settle down or the slurry may tend to “run”. Therefore test equipment was fabricated for judging the following characteristics. 

(1) Self-compatibility: The U-tube test gives an indication of the resistance of the mixture to flow round obstructions in a U-type mould. This test also detects the tendency of the coarse aggregate particles to stay back or settle down, when the mixture flows through closely-spaced reinforcements.

(2) Deformability: The slump flow test as specified by the Japan Society of Civil Engineers (JSCE) judges the ability of concrete to deform under its own weight against the friction of the base, this test, however, cannot evaluate whether the concrete will pass through the space between the reinforcement bars. This test is useful also as a routine control test, to detect the tendency for slurry to separate from the mixture.

(3) Viscosity: Viscosity of the mortar phase is obtained by a V-funnel apparatus, this is useful for adjusting the powder content, water content and admixture dosage. 

(4) Filling ability test: It is also used to determine the ability of the concrete to deform readily through closely spaced obstacles.

Many different methods have been developed to characterise the properties of SCC. No single method has been found till date which characterises all the relevant workability aspects and hence, each mixed has been tested by more than one test method for the different workability parameters. 

.

THE EXPERIMENTAL STUDY OF SELF COMPACTING CONCRETE USING PLANTAIN LEAF ASH



TYPE IN YOUR TOPIC AND CLICK SEARCH.






RESEARCHWAP.ORG

Researchwap.org is an online repository for free project topics and research materials, articles and custom writing of research works. We’re an online resource centre that provides a vast database for students to access numerous research project topics and materials. Researchwap.org guides and assist Postgraduate, Undergraduate and Final Year Students with well researched and quality project topics, topic ideas, research guides and project materials. We’re reliable and trustworthy, and we really understand what is called “time factor”, that is why we’ve simplified the process so that students can get their research projects ready on time. Our platform provides more educational services, such as hiring a writer, research analysis, and software for computer science research and we also seriously adhere to a timely delivery.

TESTIMONIES FROM OUR CLIENTS


Please feel free to carefully review some written and captured responses from our satisfied clients.

  • "Exceptionally outstanding. Highly recommend for all who wish to have effective and excellent project defence. Easily Accessable, Affordable, Effective and effective."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "I saw this website on facebook page and I did not even bother since I was in a hurry to complete my project. But I am totally amazed that when I visited the website and saw the topic I was looking for and I decided to give a try and now I have received it within an hour after ordering the material. Am grateful guys!"

    Hilary Yusuf, United States International University Africa, Nairobi, Kenya.
  • "Researchwap.org is a website I recommend to all student and researchers within and outside the country. The web owners are doing great job and I appreciate them for that. Once again, thank you very much "researchwap.org" and God bless you and your business! ."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "Great User Experience, Nice flows and Superb functionalities.The app is indeed a great tech innovation for greasing the wheels of final year, research and other pedagogical related project works. A trial would definitely convince you."

    Lamilare Valentine, Kwame Nkrumah University, Kumasi, Ghana.
  • "I love what you guys are doing, your material guided me well through my research. Thank you for helping me achieve academic success."

    Sampson, University of Nigeria, Nsukka.
  • "researchwap.com is God-sent! I got good grades in my seminar and project with the help of your service, thank you soooooo much."

    Cynthia, Akwa Ibom State University .
  • "Sorry, it was in my spam folder all along, I should have looked it up properly first. Please keep up the good work, your team is quite commited. Am grateful...I will certainly refer my friends too."

    Elizabeth, Obafemi Awolowo University
  • "Am happy the defense went well, thanks to your articles. I may not be able to express how grateful I am for all your assistance, but on my honour, I owe you guys a good number of referrals. Thank you once again."

    Ali Olanrewaju, Lagos State University.
  • "My Dear Researchwap, initially I never believed one can actually do honest business transactions with Nigerians online until i stumbled into your website. You have broken a new legacy of record as far as am concerned. Keep up the good work!"

    Willie Ekereobong, University of Port Harcourt.
  • "WOW, SO IT'S TRUE??!! I can't believe I got this quality work for just 3k...I thought it was scam ooo. I wouldn't mind if it goes for over 5k, its worth it. Thank you!"

    Theressa, Igbinedion University.
  • "I did not see my project topic on your website so I decided to call your customer care number, the attention I got was epic! I got help from the beginning to the end of my project in just 3 days, they even taught me how to defend my project and I got a 'B' at the end. Thank you so much researchwap.com, infact, I owe my graduating well today to you guys...."

    Joseph, Abia state Polytechnic.
  • "My friend told me about ResearchWap website, I doubted her until I saw her receive her full project in less than 15 miniutes, I tried mine too and got it same, right now, am telling everyone in my school about researchwap.com, no one has to suffer any more writing their project. Thank you for making life easy for me and my fellow students... Keep up the good work"

    Christiana, Landmark University .
  • "I wish I knew you guys when I wrote my first degree project, it took so much time and effort then. Now, with just a click of a button, I got my complete project in less than 15 minutes. You guys are too amazing!."

    Musa, Federal University of Technology Minna
  • "I was scared at first when I saw your website but I decided to risk my last 3k and surprisingly I got my complete project in my email box instantly. This is so nice!!!."

    Ali Obafemi, Ibrahim Badamasi Babangida University, Niger State.
  • To contribute to our success story, send us a feedback or please kindly call 2348037664978.
    Then your comment and contact will be published here also with your consent.

    Thank you for choosing researchwap.com.